FAMAG Auger Bits Series 1410

The rounded single spur of these bits cut a clean edge of the hole and the chisel-like cutting edge turns around the threaded center and removes chip by chip within the previously cut circle.

These Auger Bits are made for softwood and European hardwood. Not suited for extreme hard tropical wood! Use a jaw brace or a power drill with low speed. Lift the running power drill from time to time to help escape of chips and cool the bit. Do not force them - use only low pressure!

How fast can I run my power drill with these bits? Speed depends on the material of the workpiece and the diameter of the bit. If you are not sure, prefer the lower speed. In hardwood the speed should be generally slower than in softwood. Bits less than 10 mm you can run more than 1000 rpm, up to 20 mm reduce to 800 rpm and bits more than 20 mm should not be runned more than 400 rpm. Manufacturers often recommend in their catalogs a higher speed to give their products a more dynamic appearance. Find the best speed by yourself! You can increase the speed of the bits once you have more experience and feel about the material.

FAMAG Auger Bits
Length 320 mm
Lewis type
Series 1410
The reliable Auger bits made by FAMAG we stock in diameters up to 30 mm.
Features:
1 chisel-like cutting-edge
1 single spur for clean edge of hole
Threaded center
Bit 8 mm and larger: hexagonal shaft
Bit 7 mm and smaller: round shaft
Sizes up to 24 mm can be used in a strong cordless screwdriver.
All measurements in mm!

Diameter mm	Shaft mm	Total length mm	Cutting length mm	Order nr.	Price
5	4.8	320	255	324300	^✱€ 13.90
6	5.8	320	255	324301	^✱€ 13.90
7	6.7	320	255	324302	^✱€ 13.90
8	7	320	255	324303	^✱€ 13.90
9	7	320	255	324304	^✱€ 13.90
10	9	320	255	324305	^✱€ 13.90
11	9	320	255	324306	^✱€ 14.90
12	11	320	255	324307	^✱€ 14.90
13	12	320	255	324308	^✱€ 15.90
14	12	320	255	324309	^✱€ 15.90
15	12	320	255	324310	^✱€ 18.30
16	12	320	255	324311	^✱€ 18.30
17	12	320	255	324312	^✱€ 19.50
18	12	320	255	324313	^✱€ 19.50
19	12	320	255	324314	^✱€ 22.50
20	12	320	255	324315	^✱€ 22.50
22	12	320	255	324316	^✱€ 26.90
24	12	320	255	324317	^✱€ 27.90
25	12	320	255	324318	^✱€ 29.90
26	12	320	255	324320	^✱€ 29.90
28	12	320	255	324321	^✱€ 33.90
30	12	320	255	324322	^✱€ 36.90

FAMAG Auger Bits extra long
Length 650 mm
Lewis type
Series 1410
These reliable long Auger bits made by FAMAG we stock in diameters up to 50 mm.
Features:
1 chisel-like cutting-edge
1 single spur for clean edge of hole
Threaded center
Hexagonal shaft dependent on size, see table
Sizes up to 24 mm can be used in a strong cordless screwdriver.
All measurements in mm!

Diameter mm	Shaft mm	Total length mm	Cutting length mm	Order nr.	Price
8	7	650	535	324400	^✱€ 25.50
10	9	650	535	324401	^✱€ 25.50
12	11	650	535	324402	^✱€ 26.50
14	12	650	535	324403	^✱€ 31.50
16	12	650	535	324404	^✱€ 35.50
18	12	650	535	324405	^✱€ 37.50
20	12	650	535	324406	^✱€ 43.50
22	12	650	535	324407	^✱€ 51.50
24	12	650	535	324408	^✱€ 53.50
26	12	650	535	324409	^✱€ 61.50
28	12	650	535	324410	^✱€ 67.50
30	12	650	535	324411	^✱€ 75.50
32	12	650	535	324412	^✱€ 92.50
34	13	650	535	324413	^✱€ 125.00
35	13	650	535	324414	^✱€ 129.00
36	13	650	535	324415	^✱€ 129.00
38	13	650	535	324416	^✱€ 179.00
40	13	650	535	324417	^✱€ 199.00
45	13	650	535	324418	^✱€ 269.00
50	13	650	535	324419	^✱€ 325.00

FAMAG Auger Bits
The longest!
Length 1080 mm
Lewis type
Series 1410
Make 1 m deep holes with these Auger Bits!
Features:
1 chisel-like cutting-edge
1 single spur for clean edge of hole
Threaded center
Hexagonal shaft dependent on size, see table
All measurements in mm!

Diameter mm	Shaft mm	Total length mm	Cutting length mm	Order nr.	Price
14	12	1080	1010	324430	^✱€ 95.00
16	12	1080	1010	324431	^✱€ 104.00
18	12	1080	1010	324432	^✱€ 115.00
20	12	1080	1010	324433	^✱€ 123.00
22	12	1080	1010	324434	^✱€ 138.00
24	12	1080	1010	324435	^✱€ 152.00
26	12	1080	1010	324436	^✱€ 167.00
28	12	1080	1010	324437	^✱€ 180.00
30	12	1080	1010	324438	^✱€ 204.00
32	12	1080	1010	324439	^✱€ 217.00