Dieter Schmid's Fine Tools
Pipe Clamps, Clamp Heads

Pipe Clamps, Clamp Heads

With a pipe you can make your own clamp head with these pipe clamps. The pipe must have a conical thread at one end to fix the part with the clamp head screw. The other part slides free on the pipe by releasing the lever. JUUMA pipe clamps do not require a thread at the end of the pipe. The length of pipe is not limited.

Note: Screw clamps are neither constructed nor intended for lifting, pulling or transportation or any other abnormal use. Improper use can cause severe personal injury or property damage.
Set of Pipe Clamps for threaded Pipes 1/2 inch
Clamp body is made of cast iron.
Pipe not included
For 1/2 inch pipes (outside diameter 21.5 mm)
Jaw height 36 mm (1-1/2 inch)
Jaw width 40 mm (1-5/8 inch)
The clamp head screw permits an adjustment of 60 mm (2-3/8 inches).
Code 300111CartPrice € 9.90
Set of Pipe Clamps for threaded Pipes 3/4 inch
Clamp body is made of cast iron.
Pipe not included
For 3/4 inch pipes (outside diameter 27 mm)
Jaw height 46 mm (1-3/4 inch)
Jaw width 50 mm (2 inch)
The clamp head screw permits an adjustment of 60 mm (2-3/8 inches).
Code 300112CartPrice € 12.90
OTORO Pipe Clamp for 3/4 inch pipes
A simple and elegant design with relatively few pieces distinguish these pipe clamp heads. The Japanese tool design firm OTORO developed these clamps, in which the screw is mounted directly in the axis or center of the pipe. This helps to prevent twisting or cupping of wood panels glued up using these tools, and allows one to increase the pressure with very little effort. A ring provided with the heads can be screwed over the open end of the pipe to prevent the sliding head from coming off the pipe (look to the left of the enlarged photo) Although the spindle’s travel of only 17 mm might seem a little short, it is entirely sufficient, as the sliding head can be brought up tight against the boards to be glued up.

Pipe and wood not included!
Cast iron housing
for 3/4 inch pipes (outside diameter 27 mm)
Jaw height 44 mm
Jaw width 45 mm
Thread travel 17 mm
Made in Taiwan
Code 330800CartPrice € 28.90
Pair Leather Clamp Pads for OTORO Pipe Clamps
Protect the surface of your workpiece with these leather pads!
Picture: OTORO pipe clamp with leather pads
Code 330805CartPrice € 3.50

JUUMA Pipe Clamp for 3/4 inch pipes
In contrast to other pipe clamps, JUUMA pipe clamps do not need a threaded pipe end. Instead, you can slide either or both clamping elements freely along the pipe. This gives you more flexibility when glueing and if you centre the clamping elements on the pipe you can prevent the workpiece from tilting when the clamps are in place. Depending on its position the folding spindle handle allows either fast or forceful clamping.

Pipe not included!
Clamp body is made of strong aluminium alloy
Spindle and clamping mechanism made of steel
For 3/4 inch pipes (outside diameter 27 mm)
Jaw height 50 mm
Jaw width 60 mm
Clamping depth 60 mm
Thread travel 70 mm

Code 330225CartPrice € 29.90
Clamp Head

Watch our customer Andrea A.
demonstrating this clamping set:


Clamping set

Classic English-style clamping device. Simply drill two or more holes through a board 25 mm (1 inch) thick to take the 10 mm bolts included with the product. This is all you need to build a versatile and rugged bar clamp that can also be used as a door frame clamp.

Cut the board to the length you need.

The spindle in the clamp head has a travel of 115 mm (4.5 inches).
The clamp body is made of cast iron.
Jaw face height 48 mm
Jaw face width 40 mm

We recommend a minimum board thickness of 30 mm. For boards under 20 mm thick there is a risk of misalignment.

Note: The screws passing through the timber section must under no circumstances compress the castings. The lugs would snap off. Always screw the nuts on by hand, tightening them with a spanner is inherently risky!
Code 300100CartPrice € 15.90
You are here:   Homepage   →   Clamps   →   Pipe Clamps, Clamp Heads