TWO CHERRIES Swan Neck Chisel
Though these chisels with their swan neck are little known in Germany they are commonly found in Old England. They are an excellent tool for cleaning out deep mortises - the base can be scraped out reasonably tidily.

Blade width	Order nr.	Price
6 mm	303904	€ 33.50
10 mm	303905	€ 33.50
12 mm	303906	€ 39.50

TWO CHERRIES Cranked Paring Chisel
Chisels with cranked blade. Very useful to clean rabbets right to the corner.

Blade width	Order nr.	Price
16 mm	C105116	€ 21.50
20 mm	C105120	€ 24.90

CROWN Cranked Paring Chisel
Made from hardened and tempered carbon steel, these Sheffield made chisels have rosewood handles with brass ferrules. Used mainly for hand paring and for reaching into deep areas otherwise not accessible.

Blade width	Order nr.	Price
6 mm	303278	€ 43.90
13 mm	303279	€ 45.30
19 mm	303280	€ 47.90

Japanese Cranked Paring Chisel "Kote Nomi"
Precision paring chisels
with laminated blade
for the finest and most accurate cuts
Total length 350 mm

Blade width	Order nr.	Price
6 mm	310036	€ 79.90
9 mm	310037	€ 79.90
12 mm	310038	€ 79.90
15 mm	310039	€ 83.90
18 mm	310040	€ 87.90

Mori Nomi - Japanese Harpoon Chisel
This chisel is used to cut and clean out blind mortises. In Japan, they do not like the look of endgrain wood, and so mortises are not usually cut through the wood, but left blind. The harpoon chisel is used with normal chisels or with a gouge. In cutting mortices, the splinters are not completely eliminated after rough cutting with a chisel. The harpoon chisel can be use to clean the inside of the mortise. The mirror side of the blade is guided along the wall of the mortise and when it hits the bottom, one gives it a light tap with a mallet. When the chisel is pulled out, the harpoon or barbed side pulls out the waste wood. This chisel is used most frequently in building Shoji screens.
Blade width 5 mm
Length of harpoon hook 14 mm
Total length 237 mm
Order nr. 310200
Price € 33.50

Sokosari Nomi - Japanese Bottom Cleaning Chisel
When a mortise has been cut almost to the desired depth, the remaining wood at the bottom can be removed with this simple tool. Because the cutting edge lies at a 90-degree angle to the shank, one can work in small mortices with precision. Before using this chisel, the remaining wood at the bottom of the mortise should be nicked or cut with a normal chisel. This iron should only be manipulated by hand, and never struck with a hammer.
Blade width 5.5 - 6 mm
Size of mirror side 6 x 5 mm
Total length 235 mm
Order nr. 310202
Price € 31.50

Kama Nomi - Japanese Sickle Chisel
This chisel, sharpened on both sides, is good for cleaning out the interior of all pointed corners. For example, fine cutting and cleaning blind dovetails. It is also useful for widening the plane blade slots in wooden Japanese plane body: its shape makes the side slots easy to reach. In general this chisel is useful for cleaning-up in angled or tight and difficult-to-reach places.
Length of sickle blade 15 mm
Total length 240 mm
Order nr. 310201
Price € 31.50

Corner Cutting Chisel
This precision made corner cutting chisel is used for cutting accurate recesses to accomodate hinges, mortices, locks. Blade made of high speed steel
Blade width 10 mm
Order nr. 300208
Price € 24.90

Corner Chisel
Many hinges and bolts have square corners, but your router leaves rounded corners. Place in the corner and strike with the hammer and you get a 90° corner. The waste you clean out with a chisel. H.S.S. blade, resharpenable, blade width 10 mm, total length 75 mm only.
Order nr. 300207
Price € 14.90

Pair of CROWN Skew Chisels
Sheffield made, right- and left-handed

Blade width	Order nr.	Price
13 mm	303275	€ 36.80
19 mm	303276	€ 43.90

Pair of TWO CHERRIES Skew Chisels
Die Beitel sind jeweils rechts und links gekröpft, damit man gut an Innenecken herankommt - von Kirschen in Remscheid! Gesamtlänge 270 mm.

Blade width	Order nr.	Price
12 mm	303990	€ 39.50
20 mm	303991	€ 45.90
26 mm	303992	€ 51.90

Set of 4 CROWN Butt Chisels
ideal for very precise hand cutting and paring of joints. This set comes in a card box or wooden box.
Total length only 150 mm (6 in.)

Blade width: 6/13/19/25 mm
in paper box
Order nr. 303269
Price € 65.90

Blade width: 6/13/19/25 mm
in wooden box
Order nr. 303270
Price € 79.90

TWO CHERRIES Butt Chisels
Total length 165 mm (6-1/2 in.)

Blade width	Order nr.	Price
6 mm	303985	€ 18.50
12 mm	303986	€ 19.60
20 mm	303987	€ 21.20
26 mm	303988	€ 23.90
Set of 4 6/12/20/26 mm in paper box	303989	€ 76.50

CROWN Paring Chisel
are used mainly for hand paring when fitting joints and for reaching into deep areas otherwise not accessible. Usually paring chisels you do not stroke with a hammer. You only use your hands, one hand guides the cutting action, the other hand pushes the chisel. Blade length 230 mm!

Blade width	Order nr.	Price
13 mm	303257	€ 37.90

Kinari Mokume Nomi (Japanese Paring Chisel)
Blade made of Suminagashi, the Japanese folded steel. The "Mokume" pattern is a multi laminated steel with distinctive layered patterns. To increase the visible and perceptible contrast between the laminate layers a controlled corrosion process is used. The core is made of Tasai Special Blue Steel, a custom made steel for Tasai. The handle is made of sandalwood. Blade bevelled at the sides and single scoop "Ura" on the mirror side. This type of chisels can easily replace smaller slicks. Made by Master Tasai in Sanjo, Province Niigata.
View complete chisels 15, 24, and 36 mm wide
View 3 blades 15, 24, and 36 mm wide
View mirror side
Total length 360 mm
Blade length 90 mm

Blade width	Order nr.	Price
15 mm	313054	€ 319.00
18 mm	313055	€ 334.00
24 mm	313056	€ 366.00
30 mm	313057	€ 419.00
36 mm	313058	€ 458.00