Bench Dogs, Bench Hold Downs, Panel Clamps, VERITAS Clamps, VERITAS Surface Clamp
Undispensible helpers in every woodshop.
VERITAS Round Bench Pups
made of solid brass. They fit into a 3/4 in. (19 mm) hole drilled in any surface. These brass pups are non-corroding and kind to your tools.
Click here to see the features!
Total length 2-3/8 in. (60 mm)
Order nr. 307964
Price Pair € 17.90
VERITAS Round Bench Dogs
made of solid brass. They fit into a 3/4 in. (19 mm) hole drilled in any surface. Brass dogs are non-corroding and kind to your tools.
Total length 4-3/8 in. (110 mm)
Order nr. 307965
Price Pair € 18.90
made of solid brass. They fit into a 3/4 in. (19 mm) hole drilled in any surface. These brass pups are non-corroding and kind to your tools.
Click here to see the features!
Total length 2-3/8 in. (60 mm)
Order nr. 307964
Price Pair € 17.90
VERITAS Round Bench Dogs
made of solid brass. They fit into a 3/4 in. (19 mm) hole drilled in any surface. Brass dogs are non-corroding and kind to your tools.
Total length 4-3/8 in. (110 mm)
Order nr. 307965
Price Pair € 18.90
Muzzles for Bench Pups, pair
For clamping a finished piece without marking it, these slip-resistant muzzles slide over the bench pups to give you a non-marring surface. They have a hard, spring-grip, plastic body with six face ribs.
Order nr. 307874
Price Pair € 2.85
Muzzles for Bench Dogs, pair
For clamping a finished piece without marking it, these slip-resistant muzzles slide over the bench dogs to give you a non-marring surface. They have a hard, spring-grip, plastic body with six face ribs.
Order nr. 307875
Price Pair € 3.45
For clamping a finished piece without marking it, these slip-resistant muzzles slide over the bench pups to give you a non-marring surface. They have a hard, spring-grip, plastic body with six face ribs.
Order nr. 307874
Price Pair € 2.85
Muzzles for Bench Dogs, pair
For clamping a finished piece without marking it, these slip-resistant muzzles slide over the bench dogs to give you a non-marring surface. They have a hard, spring-grip, plastic body with six face ribs.
Order nr. 307875
Price Pair € 3.45
Low Profile Plastic Bench Dogs
These plastic bench dogs fit into a 19 mm (3/4 in.) hole drilled in any surface. With a profile height of only 13 mm these bench dogs are suitable for flat and delicate workpieces. If you already ruined a plane blade at a bench dog, you will appreciate these plastic parts for any work close to the dogs. Also suitable as replacement bench dogs for children's workbenches.
Clamping surface 13 x 37 mm (1/2 x 1-7/16 in.)
Shaft diameter 19 mm (3/4 in.)
Shaft length 38 mm (1-1/2 in.)
Order nr. 300016
Price Set of 4 pieces € 4.90
These plastic bench dogs fit into a 19 mm (3/4 in.) hole drilled in any surface. With a profile height of only 13 mm these bench dogs are suitable for flat and delicate workpieces. If you already ruined a plane blade at a bench dog, you will appreciate these plastic parts for any work close to the dogs. Also suitable as replacement bench dogs for children's workbenches.
Clamping surface 13 x 37 mm (1/2 x 1-7/16 in.)
Shaft diameter 19 mm (3/4 in.)
Shaft length 38 mm (1-1/2 in.)
Order nr. 300016
Price Set of 4 pieces € 4.90
VERITAS Low Profile Bench Dog (Bench Blade)
This is essentially a low-profile bench dog with a quick-release sliding jaw for holding work. Dubbed a "blade" due to its flat design, it projects just 1/4" (6.3 mm) above a work surface to permit maximum access to a workpiece. Used much like a toggle clamp, it has a thumb-operated eccentric cam lever to control the sliding jaw, so you can quickly secure or release work.
With 1/4" (6.3 mm) range of travel, the jaw has limited throw, but applies up to 300 lb of clamping force. Flats on the cam provide secure stops at 1/8" (3.2 mm) and 1/4" (6.3 mm) of travel. The jaw face has a 5° inward cant to help hold wood securely. The cam and jaw are cast steel, heat-treated for surface hardness, and the post and wedge-lock mechanism are turned steel.
The standard post version is for use in a 3/4" (19 mm) diameter through-hole - or blind holes that are at least 1-7/8" 48 mm) deep. The wedge-lock version is usable at any angle from horizontal to vertical, and anchors firmly in any 3/4" (19 mm) diameter through-hole in material as thin as 5/8" (16 mm) (depending on the strength of the material), or in blind holes that are a minimum of 1-7/16" (36 mm) deep.
Clamping surface 38 x 6.3 mm (1-1/2 x 1/4 in.)
Shaft diameter 19 mm (3/4 in.)
Shaft length Standard Version 47 mm (1-7/8 in.)
Shaft length Wedge-Lock Version 36 mm (1-7/16 in.)
Low Profile Bench Dog (Bench Blade), Standard Post
Price for one piece!
Order nr. 308616
Price € 16.50
Low Profile Bench Dog (Bench Blade), Wedge-Lock Post
Price for one piece!
Order nr. 308617
Price € 22.50
This is essentially a low-profile bench dog with a quick-release sliding jaw for holding work. Dubbed a "blade" due to its flat design, it projects just 1/4" (6.3 mm) above a work surface to permit maximum access to a workpiece. Used much like a toggle clamp, it has a thumb-operated eccentric cam lever to control the sliding jaw, so you can quickly secure or release work.
With 1/4" (6.3 mm) range of travel, the jaw has limited throw, but applies up to 300 lb of clamping force. Flats on the cam provide secure stops at 1/8" (3.2 mm) and 1/4" (6.3 mm) of travel. The jaw face has a 5° inward cant to help hold wood securely. The cam and jaw are cast steel, heat-treated for surface hardness, and the post and wedge-lock mechanism are turned steel.
The standard post version is for use in a 3/4" (19 mm) diameter through-hole - or blind holes that are at least 1-7/8" 48 mm) deep. The wedge-lock version is usable at any angle from horizontal to vertical, and anchors firmly in any 3/4" (19 mm) diameter through-hole in material as thin as 5/8" (16 mm) (depending on the strength of the material), or in blind holes that are a minimum of 1-7/16" (36 mm) deep.
Clamping surface 38 x 6.3 mm (1-1/2 x 1/4 in.)
Shaft diameter 19 mm (3/4 in.)
Shaft length Standard Version 47 mm (1-7/8 in.)
Shaft length Wedge-Lock Version 36 mm (1-7/16 in.)
Low Profile Bench Dog (Bench Blade), Standard Post
Price for one piece!
Order nr. 308616
Price € 16.50
Low Profile Bench Dog (Bench Blade), Wedge-Lock Post
Price for one piece!
Order nr. 308617
Price € 22.50
VERITAS Wonder Pup
This clamping bench dog does everything, clamping any angle, any shape and you can use it as tail vise. It can be used anywhere you can drill a 3/4 in. (19 mm) hole. The dog ist drilled and tapped at a 3° angle to ensure that work is held tight to the bench. Click here to see more features!
Shaft length 2-3/4 in. (70 mm)
Order nr. 307967
Price € 26.90
VERITAS Wonder Dog
as above but Shaft length 6-1/2 in. (165 mm)
Order nr. 307968
Price € 29.90
This clamping bench dog does everything, clamping any angle, any shape and you can use it as tail vise. It can be used anywhere you can drill a 3/4 in. (19 mm) hole. The dog ist drilled and tapped at a 3° angle to ensure that work is held tight to the bench. Click here to see more features!
Shaft length 2-3/4 in. (70 mm)
Order nr. 307967
Price € 26.90
VERITAS Wonder Dog
as above but Shaft length 6-1/2 in. (165 mm)
Order nr. 307968
Price € 29.90
Set of 2 Bench Holddowns
Secure your benchtop projects with this fully adjustable hold down. The only requirements are 3/4 in. (19 mm) holes. The shaft is made of a chromed steel pipe and has barb-shaped grooves to resist upward forces. Pressure plates are covered with gum pads to protect delicate workpieces. Handle is made of plastic.
Maximum working height 150 mm
Length of shaft 175 mm
Clamping depth 120 mm
Order nr. 300019
Price Set of 2 € 14.90
Secure your benchtop projects with this fully adjustable hold down. The only requirements are 3/4 in. (19 mm) holes. The shaft is made of a chromed steel pipe and has barb-shaped grooves to resist upward forces. Pressure plates are covered with gum pads to protect delicate workpieces. Handle is made of plastic.
Maximum working height 150 mm
Length of shaft 175 mm
Clamping depth 120 mm
Order nr. 300019
Price Set of 2 € 14.90
Short Post only 140 mm (5-1/2 inch) long for Bench Holddown
For use in holes where through travel is limited, this retrofit shorter hold-down post (B) is available separately. It provides about 100 mm (4 inch) of clamping capacity.
Order nr. 307963
Price € 7.90
For use in holes where through travel is limited, this retrofit shorter hold-down post (B) is available separately. It provides about 100 mm (4 inch) of clamping capacity.
Order nr. 307963
Price € 7.90
VERITAS Surface Clamp
This fast-acting surface clamp can be used anywhere you can drill a 3/4 in. (19 mm) diameter hole. The post has a wedging mechanism that anchors it firmly (horizontally or vertically) in material as thin as 5/8 in. (16 mm) (depending on the strength of the material), making it ideal for use in jigs and fixtures, e.g., sliding tables for saws. The clamp arm (which slides easily on the post when tilted, but locks at 90°) has a 2-1/8 in. (54 mm) throat depth and can grip anything from veneer to material up to 3 in. (76 mm) thick.
Anchor wedging is controlled by the brass knob on the post and clamping pressure by the knob at the arm tip. Used horizontally, the post collar acts as a material support. Used vertically, the collar is a rub ring that protects workpieces from accidental damage by the post rings. Precision machined from brass, steel and anodized aluminum, this is a versatile work support and clamp.
Large pictures
Instructions
Order nr. 307869
Price € 57.50
This fast-acting surface clamp can be used anywhere you can drill a 3/4 in. (19 mm) diameter hole. The post has a wedging mechanism that anchors it firmly (horizontally or vertically) in material as thin as 5/8 in. (16 mm) (depending on the strength of the material), making it ideal for use in jigs and fixtures, e.g., sliding tables for saws. The clamp arm (which slides easily on the post when tilted, but locks at 90°) has a 2-1/8 in. (54 mm) throat depth and can grip anything from veneer to material up to 3 in. (76 mm) thick.
Anchor wedging is controlled by the brass knob on the post and clamping pressure by the knob at the arm tip. Used horizontally, the post collar acts as a material support. Used vertically, the collar is a rub ring that protects workpieces from accidental damage by the post rings. Precision machined from brass, steel and anodized aluminum, this is a versatile work support and clamp.
Large pictures
Instructions
Order nr. 307869
Price € 57.50
VERITAS Surface Vise
This clamp combines the holding functions of a quick-release tail vise with the portability of a bench dog. It can be positioned at any angle — vertical through horizontal — and, since work is held between the jaw and any fixed work stop, clamping capacity is limited only by the size of the mounting surface.
The double posts mount in 3/4 in. (19 mm) holes. The forward post has a clearance hole to guide the clamping rod, and a wedging mechanism that anchors it firmly in through-holes in material as thin as 1 in. (25 mm) (depending on the strength of the material) or in blind holes at least 1-5/16 in. (33 mm) deep. The rear post seats in blind holes at least 2 in. (51 mm) deep and has a quick-release mechanism for adjusting the projection of the rod.
More information
Instructions
Order nr. 307749
Price € 68.00
This clamp combines the holding functions of a quick-release tail vise with the portability of a bench dog. It can be positioned at any angle — vertical through horizontal — and, since work is held between the jaw and any fixed work stop, clamping capacity is limited only by the size of the mounting surface.
The double posts mount in 3/4 in. (19 mm) holes. The forward post has a clearance hole to guide the clamping rod, and a wedging mechanism that anchors it firmly in through-holes in material as thin as 1 in. (25 mm) (depending on the strength of the material) or in blind holes at least 1-5/16 in. (33 mm) deep. The rear post seats in blind holes at least 2 in. (51 mm) deep and has a quick-release mechanism for adjusting the projection of the rod.
More information
Instructions
Order nr. 307749
Price € 68.00
VERITAS Bench Stud
Designed primarily for concealed use, this versatile hold-down can be used anywhere you can drill a 3/4 inch (19 mm) diameter hole. Its post has a wedging mechanism controlled by a swivel handle to anchor it firmly (in any orientation) in throughholes in material as thin as 5/8 inch (16 mm) (depending on the strength of the material) or in blind holes (for concealed applications) a minimum of 1-1/4 inch (32 mm) deep. With a 5 inch (127 mm) long threaded post, and a large diameter wing nut for tightening, it can be used on work surfaces up to 4-1/8 inch (105 mm) thick through a 1/2 inch (13 mm) diameter or larger dog hole.
All-steel construction, it is ideal for holding fences, making work stops and workshmop aids, securing carvings (picture left), etc. Enlargement and examples how to use
Order nr. 308615
Price € 27.50
Designed primarily for concealed use, this versatile hold-down can be used anywhere you can drill a 3/4 inch (19 mm) diameter hole. Its post has a wedging mechanism controlled by a swivel handle to anchor it firmly (in any orientation) in throughholes in material as thin as 5/8 inch (16 mm) (depending on the strength of the material) or in blind holes (for concealed applications) a minimum of 1-1/4 inch (32 mm) deep. With a 5 inch (127 mm) long threaded post, and a large diameter wing nut for tightening, it can be used on work surfaces up to 4-1/8 inch (105 mm) thick through a 1/2 inch (13 mm) diameter or larger dog hole.
All-steel construction, it is ideal for holding fences, making work stops and workshmop aids, securing carvings (picture left), etc. Enlargement and examples how to use
Order nr. 308615
Price € 27.50
VERITAS Bench Anchor
This bench anchor secures in any 3/4 inch (19 mm) diameter hole. It is self-anchoring and removable. Usable horizontally, vertically or at any angle in between, it accepts 1/2-13 threaded bolts, and will wedge in through-holes in material as thin as 5/8 inch (16 mm) (depending on the strength of the material) or in blind holes 1-1/4 inch (32 mm) deep. The anchor has a wedging mechanism controlled by an integral hex-head screw drive and an external rubber O-ring that uses friction to hold it in place during installation.
With 3/8 inch (9.5 mm) of internal thread travel, the anchor is designed to secure materials of known thickness using a fixed length fastener (for example, fastening 3/4 inch (19 mm) thick material with a 1 inch (25 mm) long machine screw). Ideal for fastening thin material, it is useful for fixing jigs, guides, etc. Best used with non-hex head drive fasteners, as the force applied with a wrench may overpower the anchor, loosening or dislodging it. All-steel construction.
Notice: threads are not metric! Use fasteners below or any 1/2-13 UNC threaded bolts!
Enlargement and examples how to use
Order nr. 308600
Price € 9.95
This bench anchor secures in any 3/4 inch (19 mm) diameter hole. It is self-anchoring and removable. Usable horizontally, vertically or at any angle in between, it accepts 1/2-13 threaded bolts, and will wedge in through-holes in material as thin as 5/8 inch (16 mm) (depending on the strength of the material) or in blind holes 1-1/4 inch (32 mm) deep. The anchor has a wedging mechanism controlled by an integral hex-head screw drive and an external rubber O-ring that uses friction to hold it in place during installation.
With 3/8 inch (9.5 mm) of internal thread travel, the anchor is designed to secure materials of known thickness using a fixed length fastener (for example, fastening 3/4 inch (19 mm) thick material with a 1 inch (25 mm) long machine screw). Ideal for fastening thin material, it is useful for fixing jigs, guides, etc. Best used with non-hex head drive fasteners, as the force applied with a wrench may overpower the anchor, loosening or dislodging it. All-steel construction.
Notice: threads are not metric! Use fasteners below or any 1/2-13 UNC threaded bolts!
Enlargement and examples how to use
Order nr. 308600
Price € 9.95
1/2-13 Threaded Fasteners for use with bench anchor
These threads are not metric! Though any 1/2-13 UNC threaded rod or bolt may be used with this bench anchor, we offer a small selection of flat-head and round-head fasteners here for convenience. The 1-1/16 inch dia. washer, for use with round-head fasteners, increases the surface contact area of the head, distributing clamping pressure while reducing the potential for fiber crushing. All are zinc-plated steel.
These threads are not metric! Though any 1/2-13 UNC threaded rod or bolt may be used with this bench anchor, we offer a small selection of flat-head and round-head fasteners here for convenience. The 1-1/16 inch dia. washer, for use with round-head fasteners, increases the surface contact area of the head, distributing clamping pressure while reducing the potential for fiber crushing. All are zinc-plated steel.
| Type | Length | Order nr. | Price |
|---|---|---|---|
| Round head | 1 inch (25.4 mm) | 308601 |
€ 0.80 |
| Round head | 1-1/4 inch (32 mm) | 308602 |
€ 0.85 |
| Round head | 1-1/2 inch (38 mm) | 308603 |
€ 0.90 |
| Round head | 2 inch (51 mm) | 308604 |
€ 0.95 |
| Washer | 1-1/16 inch (27 mm) | 308605 |
€ 0.45 |
| Flat head | 1 inch (25.4 mm) | 308606 |
€ 0.80 |
| Flat head | 1-1/4 inch (32 mm) | 308607 |
€ 0.85 |
| Flat head | 1-1/2 inch (38 mm) | 308608 |
€ 0.90 |
| Flat head | 2 inch (51 mm) | 308609 |
€ 0.95 |
Bormax Forstner Bit 3/4 inch
Do not omitt to get the right bits for the Veritas bench dogs. This Forstner bit comes from Famag in Remscheid/Germany and is good for many holes. If you already own a 19 mm drill bit, it will do as well. More Forstner Bits
Diameter 3/4 inch = 19.05 mm
Cutting length 57 mm
Total length 90 mm
Diameter of shaft 8 mm
Order nr. 304655
Price € 24.50
Do not omitt to get the right bits for the Veritas bench dogs. This Forstner bit comes from Famag in Remscheid/Germany and is good for many holes. If you already own a 19 mm drill bit, it will do as well. More Forstner Bits
Diameter 3/4 inch = 19.05 mm
Cutting length 57 mm
Total length 90 mm
Diameter of shaft 8 mm
Order nr. 304655
Price € 24.50
Extension
The cutting length of the Forstner bit above can be extended up to 150 mm.
Order nr. 304541
Price € 22.30
The cutting length of the Forstner bit above can be extended up to 150 mm.
Order nr. 304541
Price € 22.30
Submersible Bench Hook
Very useful to fix small workpieces on the top of the bench. Simply mount this bench hook on any edge of a workbench or working table with 2 screws (not included). Clamping height up to 50 mm. The jaw is 28 mm wide and 4 mm high. Made of steel, body powder oxide finish. The shaft diameter is 18 mm which makes it possible to use the hook in 19 mm holes (picture below).
Order nr. 307790
Price € 32.00
Very useful to fix small workpieces on the top of the bench. Simply mount this bench hook on any edge of a workbench or working table with 2 screws (not included). Clamping height up to 50 mm. The jaw is 28 mm wide and 4 mm high. Made of steel, body powder oxide finish. The shaft diameter is 18 mm which makes it possible to use the hook in 19 mm holes (picture below).
Order nr. 307790
Price € 32.00
Pair of Bench Dogs small
made of steel
Shaft: 20 x 16 mm / head: 25 x 16 mm
Length: 140 mm
Order nr. 303172
Price € 27.50
made of steel
Shaft: 20 x 16 mm / head: 25 x 16 mm
Length: 140 mm
Order nr. 303172
Price € 27.50
Pair of Bench Dogs medium sized
made of steel
Shaft: 20 x 20 mm / head: 25 x 20 mm
Length: 180 mm
Order nr. 303173
Price € 36.50
made of steel
Shaft: 20 x 20 mm / head: 25 x 20 mm
Length: 180 mm
Order nr. 303173
Price € 36.50
Pair of Bench Dogs large
These are commonly used for professional workbenches
made of steel
Shaft: 27 x 20 mm / head: 35 x 20 mm
Length: 225 mm
Order nr. 303174
Price € 39.95
These are commonly used for professional workbenches
made of steel
Shaft: 27 x 20 mm / head: 35 x 20 mm
Length: 225 mm
Order nr. 303174
Price € 39.95
Round Bench Dogs made of Aluminium
Ideal for large workbenches, these bench dogs have a clamping face 100 x 28 mm (top 20 mm) large to save the surface of workpieces. The 3° inclined face pulls work down to the bench surface. A locking mechanism holds the bench dog in place.
Notice: The diameter of these bench dogs is exactly 30 mm. You need to drill the hole slightly larger, 30.2 mm or 1-3/16 inch drill bit is fine.
Diameter 30 mm
Total length 200 mm
Clamping face height 100 mm
Clamping face width top 20 mm
Clamping face width bottom 28 mm
Weight 750 g
Order nr. 300502
Price Pair€ 39.95
Ideal for large workbenches, these bench dogs have a clamping face 100 x 28 mm (top 20 mm) large to save the surface of workpieces. The 3° inclined face pulls work down to the bench surface. A locking mechanism holds the bench dog in place.
Notice: The diameter of these bench dogs is exactly 30 mm. You need to drill the hole slightly larger, 30.2 mm or 1-3/16 inch drill bit is fine.
Diameter 30 mm
Total length 200 mm
Clamping face height 100 mm
Clamping face width top 20 mm
Clamping face width bottom 28 mm
Weight 750 g
Order nr. 300502
Price Pair€ 39.95
Round Bench Dogs made of Steel
Features as above, but made of steel!
Notice: The diameter of these bench dogs is exactly 30 mm. You need to drill the hole slightly larger, 30.2 mm or 1-3/16 inch drill bit is fine.
Diameter 30 mm
Total length 200 mm
Clamping face height 100 mm
Clamping face width top 20 mm
Clamping face width bottom 28 mm
Weight 2000 g
Order nr. 300503
Price Pair€ 39.95
Features as above, but made of steel!
Notice: The diameter of these bench dogs is exactly 30 mm. You need to drill the hole slightly larger, 30.2 mm or 1-3/16 inch drill bit is fine.
Diameter 30 mm
Total length 200 mm
Clamping face height 100 mm
Clamping face width top 20 mm
Clamping face width bottom 28 mm
Weight 2000 g
Order nr. 300503
Price Pair€ 39.95
Double Cutter Machine Centre Bit for round bench dogs
This is the bit to make the appropriate holes for 30 mm round bench dogs. Made by Clifton in England.
Diameter 1-3/16 inch (30.16 mm)
Total length 5-1/2 inch (140 mm)
Shank diameter 1/2 inch (12.7 mm
Order nr. 303698
Price € 39.00
This is the bit to make the appropriate holes for 30 mm round bench dogs. Made by Clifton in England.
Diameter 1-3/16 inch (30.16 mm)
Total length 5-1/2 inch (140 mm)
Shank diameter 1/2 inch (12.7 mm
Order nr. 303698
Price € 39.00
