Ryoba - Japanese Saw with ripcut and crosscut edge

The Ryoba is a saw for deep cuts both crosscut and ripcut. Picture: Dividing a 2 cm thick and 80 cm long board with a ryoba. This was finished within a few minutes.

Ryoba "Ecoprofi"
A fast, sturdy universal saw - ideal for deep cuts both across and with the grain - in the workshop or building site. The saw can be taken apart in one movement - great for small toolbags. Made by BAKUMA. It is not recommended to use different sizes of blades in one handle. Different blade thickness attracts different blade holder! The saw with the 300mm-blade is the best for the large pieces of wood! The saw with blade length 250 mm is our most sold saw and the best for general woodworking. With impulse hardened teeth! Instructions for use
Please have a look to our Saw Sets.
Classes: Order 10 or more for € 23.90 each only!

Type Blade length	Blade thickness	Kerf	Pitch crosscut	Pitch ripcut	Order nr.	Price
Ryoba 250 mm	0.5 mm	0.7 mm	18 TPI (1.4 mm)	9 TPI (3 mm)	309310	€ 25.90
Repl. Blade 250 mm					309311	€ 16.00
Ryoba 265 mm	0,6 mm	0,9 mm	14 TPI (1.8 mm)	7 TPI (3.5 mm)	309312	€ 26.90
Repl. Blade 265 mm					309313	€ 16.50
Ryoba 300 mm	0,7 mm	1,1 mm	13 TPI (2 mm)	5 TPI (5 mm)	309314	€ 34.90
Repl. Blade 300 mm					309315	€ 22.50
	Leather sheath for Bakuma Ryoba 250 and 265 mm				109053	€ 4.95
	Leather sheath for Bakuma Ryoba 300 mm				109054	€ 1.95

KIJIMA Ryoba
an extraordinary fine, precise and fast saw - for fine cabinetry. Our top brand among those with exchangeable blades. These saws are resharpenable. The entire blade is made of very hard steel. The whole blade is grinded from thick material and the original thickness is kept in the shaft of the blade. So there is no need for any chucks, screws or levers in the blade area limiting the capacity. Thus you can use the whole blade conveniently. Not for beginners! Why?

Type Blade length	Blade thickness	Kerf	Pitch crosscut	Pitch ripcut	Order nr.	Price
Kijima Ryoba 180 mm	0,3 mm	0,5 mm	23 TPI (1.1 mm)	9 TPI (3 mm)	309455	€ 58.00
Repl. Blade 180 mm					309456	€ 42.00
Kijima Ryoba 210 mm	0.38 mm	0.6 mm	21 TPI (1.2 mm)	7 TPI (3.5 mm)	309457	€ 58.00
Repl. Blade 210 mm					309458	€ 42.00
Kijima Ryoba 240 mm	0.44 mm	0.7 mm	17 TPI (1.5 mm)	7 TPI (3.5 mm)	309459	€ 58.00
Repl. Blade 240 mm					309460	€ 42.00
Kijima Ryoba 270 mm	0.6 mm	0.8 mm	15 TPI (1.7 mm)	6 TPI (4 mm)	309461	€ 58.00
Repl. Blade 270 mm					309462	€ 42.00
Kijima Ryoba 300 mm	0.65 mm	1.1 mm	10 TPI (2.5 mm)	5.5 TPI (4.5 mm)	309463	€ 63.00
Repl. Blade 300 mm					309464	€ 45.00

KIJIMA Ryoba
with impulse hardened teeth
The same production process as above but the very hard material is impulse hardened additionally. The blades of this saw fit the other Kijima ryoba handles too. Not for beginners! Why?

Type Blade length	Blade thickness	Kerf	Pitch crosscut	Pitch ripcut	Order nr.	Price
Ryoba 210 mm impulse h.	0.38 mm	0.6 mm	21 TPI (1.2 mm)	7 TPI (3.5 mm)	309469	€ 62.00
Repl. Blade 210 mm impulse h.					309470	€ 46.00
Ryoba 240 mm impulse h.	0.44 mm	0.7 mm	17 TPI (1.5 mm)	7 TPI (3.5 mm)	309471	€ 62.00
Repl. Blade 240 mm impulse h.					309472	€ 46.00
Ryoba 270 mm impulse h.	0.6 mm	0.8 mm	15 TPI (1.7 mm)	6 TPI (4 mm)	309473	€ 62.00
Repl. Blade 270 mm impulse h.					309474	€ 46.00

Verzahnung für Querschnitte auf beiden Seiten

Impulse hardened KIJIMA replacement blades with crosscut teeth on both sides
These blades are useful for all those, who only cut across the grain. One side is for coarse cuts, the other side for fine cuts. These blades fit all KIJIMA Ryoba handles.

Type Blade length	Blade thickness	Kerf	Pitch fine edge	Pitch coarse edge	Order nr.	Price
Blade 210 mm impuls h. Both edges crosscut	0.38 mm	0.6 mm	28 TPI (0.9 mm)	21 TPI (1.2 mm)	309489	€ 46.00
Blade 240 mm impuls h. Both edges crosscut	0.44 mm	0.7 mm	25 TPI (1 mm)	17 TPI (1.5 mm)	309491	€ 46.00
Blade 270 mm impuls h. Both edges crosscut	0.6 mm	0.8 mm	15 TPI (1.7 mm)	11.5 TPI (2.2 mm)	309493	€ 46.00

KIJIMA Delta Saw
Special ryoba saw for narrow places. The teeth of this saw are impulse hardened. The blade is interchangeable with all other Kijima ryoba saws. Not for beginners! Why?

Type Blade length	Blade thickness	Kerf	Pitch crosscut	Pitch ripcut	Order nr.	Price
Delta Saw 210 mm	0.5 mm	0.7 mm	25 TPI (1 mm)	9 TPI (2.7 mm)	309480	€ 62.00
Repl. Blade 210 mm					309481	€ 46.00

SILKY Ryoba Saw "Hibiki"
The "Mirai-Me" teeth cut with 4 cutting angles into the wood and are suitable for ripcut and crosscut. They leave a smooth surface after cutting. The blade is impulse hardened. The blade can be removed easily to store in a tool box.

Ryoba von Silky

The rubber handle offers superior grip. The teeth are non-set and taper ground. Thus the blade is thicker at the tooth edge than in the middle of the blade. It has the same effect as setting a saw with the advantage, that the cut is smoother and it is easier to hold the direction you want.

This saw is available in two types:
1. with large teeth (black handle). The blade has 15 TPI on one side and 10 TPI on the other side.
2. with fine teeth (white handle). The blade has 20 TPI on one side and 15 TPI on the other side.
Blades can be exchanged among each other. Comes with holster to carry on belt!

Type/Blade length	Kerf	Pitch	Order nr.	Price
Hibiki large teeth Blade 210 mm	0.95 mm	18 and 12 per 30 mm (15 and 10 TPI)	309434	€ 43.00
Repl. Blade large teeth			309435	€ 26.00
Hibiki small teeth Blade 210 mm	0.95 mm	24 and 18 per 30 mm (20 und 15 TPI)	309446	€ 43.00
Repl. Blade small teeth			309447	€ 26.00

This small traditional Ryoba allows fast and clean cuts! Blade not exchangeable! Total length 320 mm. Enlargement!
Click here to see the sister Dozuki!

Traditional Mini-Ryoba
with wooden handle
Blade length 120 mm (4-3/4 in.)
Blade thickness 0.35 mm
Kerf 0.5 mm
Pitch crosscut edge 25 TPI (1 mm)
Pitch ripcut edge 12 TPI (2 mm)
Order nr. 312053

Price € 23.50

This saw will be one of your favourite saws in a short time of use! hand forged! Not for beginners! Why? Enlargement!

Handmade small Ryoba
Blade length 135 mm (5-3/8 in.)
Blade thickness 0.25 mm
Kerf 0.45 mm
Pitch crosscut edge 25 TPI (1 mm)
Pitch ripcut edge 12 TPI (2 mm)
Order nr. 312055

Price € 92.00

made by the same small saw smithy in Miki City, Japan, who makes the handmade small ryoba. The blade is tapered to the middle to avoid jamming. This feature makes this saw to a special piece. Not for beginners! Why? Enlargement

Traditional Ryoba
Blade length 210 mm (8-1/4 in.)
Blade thickness:
- middle of blade 0.25 mm
- near the edges 0.35 mm
Pitch crosscut edge 21 TPI (1.2 mm)
Pitch ripcut edge 10 TPI (2.5 mm)
Order nr. 312057

Price € 76.50

Saw storage and protection

Leather bag for 3 Japanese saws
suitable for all saws up to 330 mm blade length
To achieve best protection and when appearance is in the second line!!
All bags: saws on pictures NOT included!
Order nr. 109056

Price € 9.95

Canvas saw holder undyed for Japanese saws
suitable for all saws up to 330 mm blade length
Notice: We recommend the canvas saw holders for the more expensive saws, even if you have to store only one saw. It simply looks better.
All bags: saws on pictures NOT included!

Canvas saw holder undyed for 3 Japanese saws
Order nr. 309858

Price € 9.50

Canvas saw holder undyed for 5 Japanese saws
Order nr. 309860

Price € 16.00

Canvas saw holder blue for 5 Japanese saws
suitable for all saws up to 330 mm blade length
All bags: saws on pictures NOT included!
Order nr. 309861

Price € 21.80

Decorative small Canvas Saw Holder for 3 Japanese Mini-Saws
suitable for all saws up to 160 mm blade length
All bags: saws on pictures NOT included!
Enlargement inside
Enlargement outside
Enlargement with saws
Order nr. 312049

Price € 29.50