Marking Knifes and Awls, Drive Pin Punches, Center Punches, Rampins
RON HOCK Spear Point Marking Knife
This right- or left-hand, spear point marking knife (the bevels are on one side only) perfect for scribing fine lines against a straight edge. The blade is hardened to Rc62 for long edge life.
Order nr. 307642
Price € 30.00
This right- or left-hand, spear point marking knife (the bevels are on one side only) perfect for scribing fine lines against a straight edge. The blade is hardened to Rc62 for long edge life.
Order nr. 307642
Price € 30.00
Shirabiki - Japanese Marking Knife
made of two layers of steel, bevel on the right side. Hand hammered asthetical surface. The blade is hardened to HRC 62-63 for long edge life.
Length 170 mm
Width 15 mm
Order nr. 309021
Price € 12.80
made of two layers of steel, bevel on the right side. Hand hammered asthetical surface. The blade is hardened to HRC 62-63 for long edge life.
Length 170 mm
Width 15 mm
Order nr. 309021
Price € 12.80
CHESTER TOOLWORKS Marking Knives
These are the nicest marking knives I ever have seen. They are made by Dave Anderson of Chester Toolworks in Chester NH USA. The nice wood for the handle he uses is only one point. The blades are made from 2.4 mm (3/32 in.) thick precision ground O-1 tool steel, are 7.9 mm (5/16 in.) wide and 32 mm (1-1/4 in.)long. The blades are individually hardened to Rockwell C 62-63 so they will hold an edge and they are shipped honed and ready to use. The total length of the knife is roughly 190 mm (7-1/2 in.).
These are the nicest marking knives I ever have seen. They are made by Dave Anderson of Chester Toolworks in Chester NH USA. The nice wood for the handle he uses is only one point. The blades are made from 2.4 mm (3/32 in.) thick precision ground O-1 tool steel, are 7.9 mm (5/16 in.) wide and 32 mm (1-1/4 in.)long. The blades are individually hardened to Rockwell C 62-63 so they will hold an edge and they are shipped honed and ready to use. The total length of the knife is roughly 190 mm (7-1/2 in.).
| Position in picture | Wood of handle | Order nr. | Price |
|---|---|---|---|
| 1. from left | Snakewood | 306000 |
€ 49.80 |
| 2. from left | Gabon Ebony | 306001 |
€ 45.00 |
| 3. from left | Brazilian Tulipwood | 306002 |
€ 45.00 |
| 4. from left | East Indian Rosewood | 306003 |
€ 45.00 |
CHESTER TOOLWORKS Awls
What is said about Chester Toolwork’s marking knives can also be said about these fine awls. These awls are designed for hand comfort and durability. The O-1 tool steel blades are taper ground and hardened to Rc 62-63 for approximately 2 inches of their length and terminate in a fine point. You can use them to start screws, mark drilling locations, or even in place of a marking knife to scribe layout lines. Total length 185 mm (roughly 7-1/4 in.).
What is said about Chester Toolwork’s marking knives can also be said about these fine awls. These awls are designed for hand comfort and durability. The O-1 tool steel blades are taper ground and hardened to Rc 62-63 for approximately 2 inches of their length and terminate in a fine point. You can use them to start screws, mark drilling locations, or even in place of a marking knife to scribe layout lines. Total length 185 mm (roughly 7-1/4 in.).
| Position in picture | Wood of handle | Order nr. | Price |
|---|---|---|---|
| 1. from top | Gabon Ebony | 306011 |
€ 39.90 |
| 2. from top | Brazilian Tulipwood | 306012 |
€ 39.90 |
| 3. from top | East Indian Rosewood | 306013 |
€ 39.90 |
STARRETT Pocket Scriber
The handle is of steel, knurled, and nickel plated. The scriber point ist steel, properly hardened and finely tapered so that the location of the point is not obscured. The scriber is held firmly in the handle by a knurled chuck and when not in use can be reversed, telescoped into the handle, and locked by the chuck. The hexagon head prevents rolling.
Length of needle 72 mm, total length 147 mm
Order nr. 306558
Price € 11.95
The handle is of steel, knurled, and nickel plated. The scriber point ist steel, properly hardened and finely tapered so that the location of the point is not obscured. The scriber is held firmly in the handle by a knurled chuck and when not in use can be reversed, telescoped into the handle, and locked by the chuck. The hexagon head prevents rolling.
Length of needle 72 mm, total length 147 mm
Order nr. 306558
Price € 11.95
STARRETT Automatic Center Punch with adjustable stroke
These punches have a mechanism which automatically strikes a blow when downward pressure is applied. No hammer is required, making one hand always free to steady the work. The force of the blow is regulated by the adjustable knurled cap. Should a heavy mark be required, the cap is screwed down. Progressivly lighter marks are obtained by turning the cap upward. The needle is made of forged steel, the handle made of lightweight aluminium.
Length: 125 mm
Diameter of handle: 16 mm
Order nr. 306502
Price € 15.70
Replacement Point
Order nr. 306497
Price € 6.50
These punches have a mechanism which automatically strikes a blow when downward pressure is applied. No hammer is required, making one hand always free to steady the work. The force of the blow is regulated by the adjustable knurled cap. Should a heavy mark be required, the cap is screwed down. Progressivly lighter marks are obtained by turning the cap upward. The needle is made of forged steel, the handle made of lightweight aluminium.
Length: 125 mm
Diameter of handle: 16 mm
Order nr. 306502
Price € 15.70
Replacement Point
Order nr. 306497
Price € 6.50
STARRETT Automatic Center Punch with adjustable stroke
Features as above but with steel handle.
STARRETT Automatic Center Punch small
New version: steel point not exchangeable!
Length: 100 mm
Diameter of handle: 11 mm
Starrett nr. 18AA
Order nr. 306500
Price € 19.50
STARRETT Automatic Center Punch large
New version: steel point not exchangeable!
Length: 125 mm
Diameter of handle: 14 mm
Starrett nr. 18A
Order nr. 306501
Price € 24.50
Features as above but with steel handle.
STARRETT Automatic Center Punch small
New version: steel point not exchangeable!
Length: 100 mm
Diameter of handle: 11 mm
Starrett nr. 18AA
Order nr. 306500
Price € 19.50
STARRETT Automatic Center Punch large
New version: steel point not exchangeable!
Length: 125 mm
Diameter of handle: 14 mm
Starrett nr. 18A
Order nr. 306501
Price € 24.50
Replacement Point
suitable for Starrett 18AA, 18A old version only
Starrett nr. PT02947
While supplies last!
Order nr. 306496
Price € 6.50
suitable for Starrett 18AA, 18A old version only
Starrett nr. PT02947
While supplies last!
Order nr. 306496
Price € 6.50
STARRETT Heavy Duty Automatic Center Punch
As above, but heavy duty version. Steel handle, high carbon steel point.
Handle diameter: 17 mm (11/16 in.)
Length: 133 mm (5-1/4 in.)
Starrett nr. 18C
Order nr. 306491
Price € 44.50
As above, but heavy duty version. Steel handle, high carbon steel point.
Handle diameter: 17 mm (11/16 in.)
Length: 133 mm (5-1/4 in.)
Starrett nr. 18C
Order nr. 306491
Price € 44.50
STARRETT Hinge-Locating Automatic Center Punch with adjustable stroke
This is the tool that carpenters, cabinetmakers, metalworkers, and home craftsmen have been waiting for. This automatic centering punch combines all the features of the above with an exclusive selfcentering locating sleeve. The locating sleeve automatically centers starter holes for screws through butt hinges and all other types of cabinet hardware items. For holes diameter 5 - 8 mm! Example
Length: 125 mm
Diameter of handle: 16 mm
Order nr. 306503
Price € 19.90
Replacement Point
suitable only for this punch!
Order nr. 306495
Price € 6.50
This is the tool that carpenters, cabinetmakers, metalworkers, and home craftsmen have been waiting for. This automatic centering punch combines all the features of the above with an exclusive selfcentering locating sleeve. The locating sleeve automatically centers starter holes for screws through butt hinges and all other types of cabinet hardware items. For holes diameter 5 - 8 mm! Example
Length: 125 mm
Diameter of handle: 16 mm
Order nr. 306503
Price € 19.90
Replacement Point
suitable only for this punch!
Order nr. 306495
Price € 6.50
STARRETT Center Punches
These center punches are made of specially selected steel, hardened and properly tempered. They are well proportioned, nicely finished and have a knurled finger grip. The points are ground at a proper angle to give maximum service, and the tips are accurately centered. Series 117. The diameter is given at top of tapered point. Click on the picture for enlarged views!
These center punches are made of specially selected steel, hardened and properly tempered. They are well proportioned, nicely finished and have a knurled finger grip. The points are ground at a proper angle to give maximum service, and the tips are accurately centered. Series 117. The diameter is given at top of tapered point. Click on the picture for enlarged views!
| Diameter | Length | Order nr. | Price |
|---|---|---|---|
| 1.5 mm | 75 mm | 306505 |
€ 4.40 |
| 2 mm | 100 mm | 306506 |
€ 4.60 |
| 2,5 mm | 100 mm | 306507 |
€ 5.10 |
| 4 mm | 100 mm | 306508 |
€ 5.60 |
Set of 5 STARRETT Center Punches
Series 117 as above with Diameters: 1.5/2.0/2.5/3.0/4.0 mm
Order nr. 306509
Price € 24.20
Series 117 as above with Diameters: 1.5/2.0/2.5/3.0/4.0 mm
Order nr. 306509
Price € 24.20
STARRETT Prick Punches
When precise positioning of a point or an intersection of lines is required, thes are the punches to use. The points are carefully ground to the correct taper, which is sharper than the normal center punch. This allows exact placement of the point, providing sharp impressions. These punches are properly hardened, tempered , and nicely finished. Series 816.
When precise positioning of a point or an intersection of lines is required, thes are the punches to use. The points are carefully ground to the correct taper, which is sharper than the normal center punch. This allows exact placement of the point, providing sharp impressions. These punches are properly hardened, tempered , and nicely finished. Series 816.
| Diameter | Length | Best.-Nr. | Price |
|---|---|---|---|
| 2 mm | 100 mm | 306512 |
€ 7.50 |
| 2,5 mm | 100 mm | 306513 |
€ 7.50 |
| 4 mm | 100 mm | 306514 |
€ 8.70 |
Combination STARRETT Punch Set of 5
Center Punches and Prick Punches
Series 117 with diameters: 1.5/2.5 mm
Series 816 with diameters: 2.0/3.0/4.0 mm
Order nr. 306515
Price € 32.30
Center Punches and Prick Punches
Series 117 with diameters: 1.5/2.5 mm
Series 816 with diameters: 2.0/3.0/4.0 mm
Order nr. 306515
Price € 32.30
STARRETT Drive Pin Punches
These Drive Pin Punches are well proportioned, hardened, and have a knurled finger grip. STARRETT-Series 565. Click on the picture for enlarged views!
These Drive Pin Punches are well proportioned, hardened, and have a knurled finger grip. STARRETT-Series 565. Click on the picture for enlarged views!
| Diameter | Length | Order nr. | Price |
|---|---|---|---|
| 1.5 mm | 100 mm | 306520 |
€ 4.40 |
| 2.5 mm | 100 mm | 306521 |
€ 4.40 |
| 3 mm | 100 mm | 306522 |
€ 4.40 |
| 4 mm | 100 mm | 306523 |
€ 4.40 |
| 5 mm | 100 mm | 306524 |
€ 4.40 |
| 5.5 mm | 100 mm | 306525 |
€ 4.40 |
| 6 mm | 100 mm | 306526 |
€ 4.40 |
| 8 mm | 100 mm | 306527 |
€ 5.20 |
| Set of 8 in plastic bag | 306528 |
€ 35.40 | |
STARRETT long Drive Pin Punches
These Drive Pin Punches are well proportioned, hardened, and have a knurled finger grip. STARRETT-Series 248. Click on the picture for enlarged view! They are designet to withstand hard use.
mm specification only approximately. These punches are made in slightly undersized inch measurements.
These Drive Pin Punches are well proportioned, hardened, and have a knurled finger grip. STARRETT-Series 248. Click on the picture for enlarged view! They are designet to withstand hard use.
mm specification only approximately. These punches are made in slightly undersized inch measurements.
| Dia- meter |
Total length |
Length drive pin section |
Order nr. |
Price |
|---|---|---|---|---|
| 3 mm (1/8 inch) | 202 mm | 88 mm | 306542 |
€ 6.95 |
| 5 mm (3/16 inch) | 202 mm | 88 mm | 306543 |
€ 6.95 |
| 6 mm (1/4 inch) | 202 mm | 88 mm | 306544 |
€ 6.95 |
| 8 mm (5/16 inch) | 202 mm | 88 mm | 306545 |
€ 6.95 |
| 9.5 mm (3/8 inch) | 202 mm | 88 mm | 306546 |
€ 6.95 |
| Set of 5 in plastic bag | 306547 |
€ 33.90 | ||
STARRETT Square Head Nail Set of 5
These Nail Sets have a round grip and a large square head that provides a large striking surface, prevents the tools from rolling, and makes them easier to find among nails or other small tools in the pocket. STARRETT-Series 800. Click on the picture for enlarged views! Total length 4 in. (102 mm.)
These Nail Sets have a round grip and a large square head that provides a large striking surface, prevents the tools from rolling, and makes them easier to find among nails or other small tools in the pocket. STARRETT-Series 800. Click on the picture for enlarged views! Total length 4 in. (102 mm.)
| For nail heads up to: | Order nr. | Price |
|---|---|---|
| 1/32 in. (0.8 mm) | 306535 |
€ 9.80 |
| 1/16 in. (1.6 mm) | 306536 |
€ 9.80 |
| 3/32 in. (2.4 mm) | 306537 |
€ 9.80 |
| 1/8 in. (3.2 mm) | 306538 |
€ 9.80 |
| 5/32 in. (4 mm) | 306539 |
€ 9.80 |
| Nail Set of 5 in Plastic Bag | 306540 |
€ 51.70 |
VERITAS Optical Center Punch
To keep a twist drill from skating on metal (and leaving you with a hole in the wrong place) you should always use a center punch, especially when using small flexible bits. The dimple created by the punch holds the bit point true. The Veritas optical center punch simplifies the procedure at the same time as it substantially increases accuracy. Even with wood there is an advantage to using a center punch; it creates a small crater that readily centers a brad-point drill. As an added bonus, you can use the 8-power optical post as an inspection monocular in your shop. It has excellent depth of field and is easily focused freehand. Instructions ...
Height of punch base: 31 mm
Diameter of punch base: 28 mm
Diameter of punch: 8 mm
Order nr. 307873
Price € 35.50
To keep a twist drill from skating on metal (and leaving you with a hole in the wrong place) you should always use a center punch, especially when using small flexible bits. The dimple created by the punch holds the bit point true. The Veritas optical center punch simplifies the procedure at the same time as it substantially increases accuracy. Even with wood there is an advantage to using a center punch; it creates a small crater that readily centers a brad-point drill. As an added bonus, you can use the 8-power optical post as an inspection monocular in your shop. It has excellent depth of field and is easily focused freehand. Instructions ...
Height of punch base: 31 mm
Diameter of punch base: 28 mm
Diameter of punch: 8 mm
Order nr. 307873
Price € 35.50
