Screw Bits, Auger Bits, Spoon Bits, Gimlets, Tapered Bit, Tapered Reamer - only for drilling by hand

Drilling by hand: Screw Bits, Auger Bits, Spoon Bits, Gimlets, Tapered Bit, Tapered Reamer

Ring Auger Bit - Made in Japan

Ring Auger Bit - Made in Japan The rounded single spur of these bits cut a clean edge of the hole and the chisel-like cutting edge turns around the threaded center and removes chip by chip within the previously cut circle. The thread of the center is large and strong enough to bite into the wood and pulls the bit. You do not have to use any pressure. This bit with large threaded center is unsuitable for power drills. For softwood and European hardwoods such as oak, beech, cherry. All measurements in mm, imperial only approximately!

Diameter mm Diameter inch Total length Spiral length Cutting length Order nr.Price
6 7/32 410 160 190
Price € 15.90
8 5/16 460 190 410
Price € 15.90
10 3/8 500 220 460
Price € 15.90
12   520 230 470
Price € 15.90
13 1/2 520 230 470
Price € 18.90
16 5/8 560 270 500
Price € 21.90
19 3/4 590 300 525
Price € 23.90
20   590 300 525
Price € 23.90
25 1 600 310 530
Price € 29.90
30   600 310 530
Price € 35.90
35   600 310 520
Price € 59.90
38 1-1/2 600 310 520 Currently not in stock!
Price € 68.90

Ring Auger Bits from old stock

Ring Auger Bits from old stock These bits have been stocked for several years and have not been used. They come in best condition. Please pay attention to the notes, some have a thicker shaft than the spiral and some do not have edge spurs. If there is no note, they come with two edge spurs. Some spurs have small burrs which must be removed with a file (only from inside please!)
Only to be turned by hand! Enlargement - see also the bits without spurs and the bits with thicker shaft.

Diameter
mm
Diameter
inch (approx.)
Total
length
Cutting length Order nr.Price Notes
6.5 approx. 1/4 470 160
Price € 6.90
Short cutting length! Shaft thicker than spirals! Colour: blue
8 5/16 470 160
Price € 8.90
Short cutting length! Shaft thicker than spirals! Colour: blue
14 9/16 455 400
Price € 10.90
Colour: red
Other sizes not available!
Gimlets with conical square shaft from old stock

Gimlets with conical square shaft from old stock These gimlets come from a German tool factory shut down a while ago. They have been stocked for several years and have not been used. They come in best condition. Made for use in a hand brace with four jaws! Picture shows 4 mm and 12 mm.

Diameter
mm
Diameter
inch
Total length
 
Cutting length
 
Order nr.Price
8 5/16 150 90
Price € 3.95
10.5 - 11 13/32 160 100
Price € 3.95
No other sizes!

Notice:

Our braces have, at the base of the chuck, a square hole to hold immobile the square end of the shaft of various kinds of bits. The size of the hole is designed to accept the most common sizes of square-ended bits. There are however a variety of square-ended bits that are too small to be securely held in the normal, 8 x 8 mm hole. So if used in this brace, they will be held only by the four jaws and can turn or come loose under pressure. With this simple, inexpensive adapter, this problem can be solved. It is a section of square brass tube. Placed in the square hole at the base of the chuck, it reduces the 8 x 8 mm hole to 6 x 6 mm to hold smaller bits firmly in place. We can unfortunately not say with certainty which bits will work and which will not in our braces, as the manufacturing tolerances for the ends of these kinds of bits are very loose. We recommend to add this adapter to your bit order.

Auger Bits with conical square shaft from old stock

Auger Bits with conical square shaft from old stock These auger bits come from a German tool factory shut down a while ago. They have been stocked for several years and have not been used. They come in best condition.

Made for use in a hand brace with four jaws! Please pay attention to the notes on the right of the table. One type is without spurs, others come with 2 spurs, there are Jennings pattern (no central straight-running core) and Center bit pattern (with central straight-running core) types. Some spurs have small burrs which must be removed with a file (only from inside please!)     An Auger bit file you find here
Only for use by hand!

Diameter
mm
Diameter
inch (approx.)
Total
length
Cutting
length
Order nr.Price Notes
 
8 5/16 200 160
Price € 5.95
2 Spurs
Center Pattern
24 15/16 240 175
Price € 4.95
Without Spurs
Jennings Pattern
26 1 240 175
Price € 10.95
2 Spurs
Center Pattern
28 1-1/8 240 175
Price € 12.95
2 Spurs
Center Pattern

Conical square shaft is a bit crooked, by using a file this can be fixed.
30 1-3/16 245 180
Price € 13.95
2 Spurs
Center Pattern
CLIFTON Parallel Spoon Bit
CLIFTON Parallel Spoon Bit
The Parallel Spoon Bits are primarily used for boring holes - either vertically or at an angle - to take the back "spokes" of Windsor chairs. Total length 4-1/2 in. = 115 mm, Cutting length 2-1/2 in. = 63 mm.
Fit many old braces but unfortunately not our braces nr. 300200 und nr. 300185, as the shank of these tools are too short.
Diameter
(inch)
Diameter
(mm)
Order nr.Price
3/8 9.5
Price € 30.90
7/16 11
Price € 32.50
1/2 13
Price € 34.10
9/16 14.3
Price € 35.20
5/8 16
Price € 38.60
3/4 19
Price € 45.60
High Quality Gimlets
High Quality Gimlets
This handy and quick-working gimlet comes from Japan. Whether you want to drill holes to take screws, hooks or nails, or simply would like to have a simple small drill at hand in your tool box, with this tool, you will always have a versatile helper that needs no electricity and will never let you down. Detail tip

Diameter Cutting length Order nr.Price
3 mm 60 mm
Price € 5.95
4 mm 70 mm
Price € 5.95
5 mm 85 mm
Price € 5.95
6 mm 85 mm
Price € 5.95
Set of 4 Gimlets
Set of 4 Gimlets
Not as precise, hard, sharp and ergonomic as the Japanese gimlet bits above but good enough for boring holes for screws and nails.
Sizes included: 2, 3, 4, 5 mm
Length 95 - 135 mm
Comes in plastic bag
Price € 3.95

 
Dieter Schmid - Fine Tools
logo
www.fine-tools.com
You are here:   Homepage   →   Drilling   →   Auger Bits   →   Drilling by hand: Screw Bits, Auger Bits, etc.
Inc VAT  |  Shipping is extra  |  Your cart  |  Fast order  |  Contact us  |  Help  |  Deutsch  |  Italiano
 |  Inc VAT Shipping is extra - view costs  |  About Us  |  Revocation right for consumers  | Terms  |  Data protection declaration  |  Battery disposal